• EI
  • Scopus
  • 食品科学与工程领域高质量科技期刊分级目录第一方阵T1
  • DOAJ
  • EBSCO
  • 北大核心期刊
  • 中国核心学术期刊RCCSE
  • JST China
  • FSTA
  • 中国精品科技期刊
  • 中国农业核心期刊
  • CA
  • WJCI
  • 中国科技核心期刊CSTPCD
  • 中国生物医学SinoMed
中国精品科技期刊2020
翟红旭,尹泽希,孙希云,等. 响应面法优化草莓混合凝胶3D打印配方[J]. 食品工业科技,2024,45(9):1−12. doi: 10.13386/j.issn1002-0306.2023040289.
引用本文: 翟红旭,尹泽希,孙希云,等. 响应面法优化草莓混合凝胶3D打印配方[J]. 食品工业科技,2024,45(9):1−12. doi: 10.13386/j.issn1002-0306.2023040289.
ZHAI Hongxu, YIN Zexi, SUN Xiyun, et al. Strawberry Mixed Gel 3D Printing Formula Optimization[J]. Science and Technology of Food Industry, 2024, 45(9): 1−12. (in Chinese with English abstract). doi: 10.13386/j.issn1002-0306.2023040289.
Citation: ZHAI Hongxu, YIN Zexi, SUN Xiyun, et al. Strawberry Mixed Gel 3D Printing Formula Optimization[J]. Science and Technology of Food Industry, 2024, 45(9): 1−12. (in Chinese with English abstract). doi: 10.13386/j.issn1002-0306.2023040289.

响应面法优化草莓混合凝胶3D打印配方

Strawberry Mixed Gel 3D Printing Formula Optimization

  • 摘要: 为提高草莓尾果利用率,扩宽草莓加工产品品类,将草莓制浆后与黄原胶、卡拉胶复配成适合3D打印的基料,并利用单因素及响应面优化试验,得到草莓混合凝胶3D打印最优配方。结果表明:不同原料对打印精度的影响大小依次为K-卡拉胶>草莓浆>黄原胶,最佳工艺配方为草莓浆添加量40 g,黄原胶添加量2 g,K-卡拉胶添加量3 g,在此条件下,测得草莓3D打印产品打印精度为98.39%,草莓3D打印产品最符合设置模型(正方体:上边长15 mm、下边长15 mm、高15 mm),此时材料能够很好地挤出且支撑能力最好。

     

    Abstract: In order to improve the utilization rate of strawberry tail fruit and expand the product categories of strawberry processing, strawberry pulping was combined with xanthan gum and carrageenan to form a base material suitable for 3D printing. The optimal formula of strawberry mixed gel 3D printing was obtained by using single factor and response surface optimization experiments. The results showed that: The influence of different raw materials on the printing accuracy was in the order of K-carrageenan>strawberry pulp>xanthan gum, and the optimal process formula was strawberry pulp additive amount of 40 g, xanthan gum additive amount of 2 g, K-carrageenan additive amount of 3 g. Under this condition, the printing accuracy of strawberry 3D printing products was 98.39%, and strawberry 3D printing products were most consistent with the set model (cube: The upper side length was 15 mm, the lower side length was 15 mm, the height was 15 mm), at this time, the material could be well extruded and the support capacity was the best.

     

/

返回文章
返回